Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - AlexH

Pages: [1] 2 3
1
Progress Reports / Re: Massacre & Friends
« on: October 27, 2015, 10:03:51 pm »
dude, i love the pulley/arm combo. build looks really clean and simple too.

2
North America / Re: Barn Battles!!! 9/6/15
« on: September 01, 2015, 01:25:38 am »


my wedge is ready

3
North America / Re: Barn Battles!!! 9/6/15
« on: August 13, 2015, 11:59:54 pm »
Alex, surely you have a DPMI that is in the ballpark range of the 12lb sumo class right?  Might as well plan on that instead of the 30s at this point...

-Zac

the big red one is being lent to someone for this but they haven't seemed to register yet. if they don't i'll bring it as a loner.

4
Questions / Re: NERC sportsman spinner limits
« on: August 13, 2015, 11:51:42 pm »
but wedge industries wanted to do the giant colsonbot

5
Event Videos / Re: Bot Blast 2015
« on: August 04, 2015, 10:13:01 pm »
you didn't get the fight that regift won. how will we ever taunt tim?

6
Progress Reports / Re: Team Ignition
« on: July 29, 2015, 10:39:13 pm »
http://killerbotics.com/kbtools/TentacleTools/


dicks version is better. its updated with current motors

7
Progress Reports / Re: Team Ignition
« on: July 27, 2015, 04:52:47 pm »


Here's my new BW design. the drive will be belt-driven 11.1 silver sparks using the new double-wide 15t pulley they sell. Weapon motor is one of these. Disc diameter is 6in. Not sure if that's too big or not. Still need to design the blade for it. Top and bottom armor will be 16mm garolite, frame rails will be made out of 1/3 uhmw. Side skirts will be cut out of some thin plastic, probably uhmw as well. Not entirely sure if it will be in weight but I can take off skirts and pocket the weapon rails if I need to.

Thoughts?

just to give you a sense of size, riptoff my 15lb's disk is 6" dia.

what design benefits do you really see by making it that big?

8
Progress Reports / Re: Twisted Sick Robotics
« on: July 27, 2015, 04:37:02 pm »
been shaping some clay. some many things yet to change but the general idea is forming.


-Kyle

i do not like where this is going...

9
Progress Reports / Re: Pnuematic Beetleweight Build
« on: July 13, 2015, 04:17:15 pm »
the dimension engineering one almost killed me when it randomly activated on my 30lb flipper. i wouldn't trust it at all.

10
Progress Reports / Re: Team Ignition
« on: June 30, 2015, 10:48:21 pm »
uhmw pro tip, drill out you corner locations and rough cut it with a jigsaw and then finish it on the mill.

11
cdo a little test. take a endmill. stick it in your cordless drill. take stock and put in benchtop vise. now try to mill it.


carbide shatters on impacts

12
Progress Reports / Re: Mutually Assured Destruction
« on: June 25, 2015, 08:09:38 pm »
that bar is still begging to be a horizontal

13
Questions / Re: Picking the right ESC
« on: June 11, 2015, 10:28:40 pm »
30 botbitz pair nicely with china drill motors

http://ttrobotics.com/botbitz-30amp-esc/

14
Event Videos / Re: Rage in the Cage 2015
« on: May 05, 2015, 04:01:30 pm »
thanks for getting good video

15
Progress Reports / Re: Bone Dead Robotics
« on: May 03, 2015, 11:45:34 pm »
A bit more of an update:



El Destructo is now a closed structure with a top plate on and the new side wheel protectors. I probably should make a more permanent solution than those screws, but they are really helpful because of the ability to adjust the height. I still need to order that bronze sleeve, but after that, I guess it will be in competition ready state.

swap those wood screws with something like 1/4" lag bolts

Pages: [1] 2 3